Machine × material · Settings

Glowforge Pro settings for anodized aluminum

Glowforge will not publish a custom anodized preset. Forum reports span 335 to full speed. None of them name the Pro, so each row is a starting estimate.

· About 5 min read

Machine
Glowforge Pro, a 45W CO2
Material
Anodized aluminum
Rows
5

Settings on this page

Job Laser Power Speed Passes Interval Focus Where it came from
Engrave CO2 15 1000 on the Glowforge scale 2 not stated not stated Starting estimate
gamn1958 wrote 1000 speed and 15 power with 2 passes for metal business cards. The post does not say Basic, Plus, or Pro. Glowforge rates the Pro at 45 watts and the Plus and Basic at 40. This is a test starting point on a Pro, not a Proofgrade preset.
Engrave CO2 25 1000 on the Glowforge scale 1 not stated not stated Starting estimate
The same owner also wrote 1000 speed and 25 power with one pass, and told people to try both. The model is still unnamed. On a 45W Pro, try the lighter 15-power row before this one. Do not rewrite 1000 as millimeters per second. Glowforge speed is their own scale.
Engrave CO2 full 335 on the Glowforge scale not stated 340 LPI, as posted not stated Starting estimate
BSheremeto wrote 335, full, 340 for small text. The thread does not name the Pro. Full power on a 45W tube is more than full power on a 40W tube. Use it as a slow, hot corner of a test, not as the first square on a customer's card.
Engrave CO2 50 700 on the Glowforge scale not stated 350 LPI in one post, not stated in the other not stated Starting estimate
One owner in the anodized thread wrote 700/50/350. dklgood, in the business-card thread, wrote 700 speed and power 50 without an LPI. Neither post names the Pro. The 350 LPI belongs to the first post only. Treat 700 and 50 as the shared part, and test the line spacing.
Engrave CO2 full 1000 on the Glowforge scale 1, and a second if blue dye remains 270 DPI, as posted not stated Starting estimate
hansepe wrote 1000/full and 270 DPI for simple graphics, and said some blue cards needed a second pass to clear the color. The post does not name the Pro. Full power at full speed is a real report. On a 45W machine it is the heavy end of the test, not a factory preset.

Read the Glowforge Pro, a 45W CO2 page and the Anodized aluminum page for the citations behind the machine and the material.

Glowforge will not hand you this preset. Their custom-materials FAQ says they cannot advise settings for material they have not approved, and that anodized aluminum is something owners engrave: the dye changes, the metal is not carved away, and it still feels smooth. The spec page lists it under engrave only. The Pro is the 45-watt Class 4 machine. The shop link is Glowforge’s, if you are still choosing a printer.

Speed on a Glowforge is a number on their slider. People say 1000 for the fast end. It is not millimeters per second. Do not type 1000 into LightBurn and expect the same mark. Power is their percent, and “full” means the top of that control. This page does not convert “full” into 100 in a case where the writer said “full.”

What the posts actually say

gamn1958, on March 19, 2021, gave two card settings: 1000 speed at 15 power for two passes, and 1000 at 25 power for one pass, and said to try both.

BSheremeto wrote “335, full, 340” for small detail. Another owner in that thread wrote that 700/50/350 worked for text, and that the machine does not cut aluminum. In the business-card thread, dklgood wrote 700 speed and power 50. hansepe wrote 1000/full and 270 DPI for simple graphics, with a second pass when blue dye remained. A separate comment in the anodized thread said the app’s MacBook preset (full speed, full power, 340 LPI) had worked on other anodized pieces. That one is left out of the table because “full speed” was not given as a digit, and a MacBook preset is Proofgrade for a laptop, not a published anodized card preset.

Glowforge staff notes on the forum say advice in Beyond the Manual is not reviewed. These rows are neighbors’ notes.

Run a test grid first

Use a scrap card from the same pack. The test grid has a Glowforge-scale preset. For this metal, a tighter net is enough: speed 700 to 1000, power 15 to 50, one pass. Put 1000 / 15 and 1000 / 25 in that net before you try “full.” Score lines are not cuts. You are only removing dye.

If the mark chars or blows the dye out

Bare, rough metal, a brown halo, or a card that warped means too much heat. Anodize is a thin dye. Step back to 1000 speed and 15 power, one pass, even if a forum post used two. Two passes of a heavy setting is how a thin card overheats. If 15 power is already too hot on your Pro, the next test is lower power at the same speed. That lower power is your test, not a number this page will invent and stick on Glowforge.

If the mark is too light

Dye still shows in the letters. Try the 25-power one-pass row, then 700 at 50, before you go to full power. Blue anodize is the color hansepe said sometimes needs a second pass. Black often clears sooner. Look at the card in room light, not only in the bed photo. A second pass of a light setting is closer to the posts than one pass at full power.

It will not cut through. If the card is still one piece, the job worked. Cutting is the wrong goal.

What would change the number

The color of the anodize, a Plus or Basic instead of a Pro, a dirty lens, and any card that is painted rather than anodized. Powder coat and bare aluminum are not this page. Galvanized metal is on Glowforge’s do-not-laser list.

Questions people ask

Why is every row an estimate?

Because the posts are real and the model is missing. Glowforge's own FAQ says forum advice in Beyond the Manual is unsupported and is not reviewed by Glowforge, and that they will not give custom settings. The Pro is 45 watts. Plus and Basic are 40. The table keeps the posted numbers and refuses to pretend they were measured on a Pro.

Can I cut the card out?

No. Glowforge lists anodized aluminum as engrave-only. Their FAQ says the mark discolors the metal and the surface still feels smooth. If you need the card cut to shape, buy it already cut.

Sources

  1. Anodized material settings — Glowforge Owners Forum
  2. Settings for engraving anodized aluminum — Glowforge Owners Forum
  3. What settings for aluminum business cards — Glowforge Owners Forum
  4. Non-Proofgrade materials FAQ — Glowforge
  5. Glowforge Performance series tech specs — Glowforge
  6. Glowforge Pro — Glowforge