Machine × material · Settings

xTool F1 settings for engraving slate

An Atomm project prints an F1 diode start of 90–100% power, 150 mm/s, and 140 lines per cm. The project itself was made on a D1 Pro.

· About 3 min read

Machine
xTool F1: 10W diode and 2W infrared
Material
Slate coasters and blanks
Rows
1

Settings on this page

Job Laser Power Speed Passes Interval Focus Where it came from
Engrave Diode 90–100% 150 mm/s not stated 140 lines per cm
140 lines per cm is 0.071 mm between lines. That gap is 10 divided by 140. The source printed the lines per cm, not the millimeters.
not stated for the F1 in this project Cited

Read the xTool F1: 10W diode and 2W infrared page and the Slate coasters and blanks page for the citations behind the machine and the material.

xTool’s F1 FAQ says the diode can engrave slate. It does not print a power or a speed. The number in the table is from an Atomm project, Custom slate charcuterie board. The project says it was made on a D1 Pro. In the settings table the author added a row for the xTool F1 diode: 90–100% power, 150 mm/s, 140 lines per cm. The author calls the whole table a starting point and says to run a small test on the back of a coaster.

That is a cited maker row. It is not an xTool EasySet preset, and it is not a log from an F1 job. Passes are not in the table. Focus for the F1 is not in the table either. The project talks about a kickstand on a D1 or S1. Do not go looking for that lever on an F1. The F1 page says focus is the red and blue dots overlapping, or a thickness you type in.

The machine, if you are buying one, starts at the xTool store. Confirm the listing. Slate blanks are on the slate page.

What 140 lines per cm means

The project printed lines per centimeter, not a millimeter gap. Ten millimeters divided by 140 is about 0.071 mm between lines. The table shows that division so you can see it. If your software asks for lines per cm, type 140. If it asks for a gap, the division is the estimate, and the 140 is the source.

Run a test grid first

Use the back of one coaster, the way the project says. Wipe the dust off first. In xTool Creative Space or xTool Studio, a material test array with power from about 70% to 100% and speed from about 100 to 250 mm/s will put 90–100% and 150 mm/s inside the grid. The test grid helper can lay those squares out. xTool’s own article on reading a grid says to pick a clear square with clean edges, not the darkest square.

Frame the job with the cover closed, or with glasses that block 455 nm and 1064 nm. That sentence is xTool’s, from their processing guide, and it is linked from the machine page.

If the mark chars or turns muddy

Slate goes pale, not black. A brown or ashy mark, or a groove that is rough instead of bright, is too much heat. Move toward 100% only if the mark is weak. If it is already rough at 90% and 150 mm/s, try a faster square in the test, still on the diode. Washing with a soft brush, which the project tells you to do, sometimes reveals a cleaner mark under the dust. Look after you wash, not before.

If the mark is too light

Focus is the first suspect. The project says a blurry focus will not go bright white. Refocus until the red and blue dots meet on the stone, then repeat one square. If focus is good and the square is still grey, step toward 100% and slightly slower than 150 mm/s, and stop when the white is even. More passes are not in the source. Do not stack passes until a single pass has failed on scrap.

The cut will not “go through.” Slate is not a cut. If you are judging the job by whether the coaster falls apart, you are running the wrong kind of job.

What would change the number

A sealed or painted slate, a thicker serving board, or the infrared laser. The optional lacquer trick in that project changes the surface, so it can change the square you pick. Let any coating cure outside the laser room. A D1 Pro row from the same table is 80–100% at 60 mm/s. That speed is for a gantry diode, not for this galvo. Do not type 60 mm/s into the F1 and call it the same setting.

Questions people ask

Is this xTool's official EasySet preset?

No. xTool's support pages tell you to pick a material in the software and then test third-party stock. This number is a maker's table on Atomm. The project header says it was made with a D1 Pro. The F1 line is the author's suggested start for an F1, and the author says to test the back of a coaster first.

Should I use the infrared laser instead?

xTool's F1 FAQ puts slate on the diode list. The infrared laser is described for metal, plastic, and black acrylic. This page does not have a sourced infrared slate speed, so it does not invent one. Use the diode row as the test, on the diode.

Sources

  1. Custom slate charcuterie board — Atomm
  2. FAQ on product information for F1 — xTool
  3. How to understand a material test array — xTool
  4. xTool F1 product introduction — xTool
  5. xTool store — xTool