Diode and infrared · Machines

xTool F1: 10W diode and 2W infrared

xTool rates the F1 at a 10W 455 nm diode plus a 2W 1064 nm infrared laser, on a 115 by 115 mm bed.

· About 3 min read

Laser
Diode and infrared
Wattage
10W diode + 2W infrared
Work area
115 × 115 mm (4.53 × 4.53 in)
Specs checked
2026-11-18

What the maker says it can do

  • Engrave with the 10W diode on paper, wood, leather, slate, dark glass, and some dark opaque acrylic, per xTool's own lists.
  • Engrave metal, plastic, and black acrylic with the 2W infrared laser, per the same support introduction.
  • Cut paper, wood, leather, MDF, felt, and some dark opaque acrylic with the diode. xTool prints 'up to 8 mm wood' and 'up to 5 mm acrylic.'

What it does not do, from the same sources

  • The base work area on the spec table is 115 × 115 mm. A large sign does not fit unless you add a slide extension, and xTool's pages do not agree on that extension's size.
  • Clear acrylic is not on the diode's engrave list. xTool says 'some dark opaque acrylic' for the diode and 'black acrylic' for the infrared laser.
  • The infrared laser is described as an engraving source for metal and plastic, not as the cutter. Cutting claims on the support page belong to the diode.

Settings written for this machine

xTool’s support introduction, updated July 27, 2023, is the spec table this page uses. The quick start guide prints the same lasers and the same 115 × 115 mm area, and it adds the electrical side: 24 V, 5 A, 120 W, model MXF-K001-LG4.

The xTool store is where a current listing would live. Confirm the listing still matches this spec table before you buy. This page does not guess whether a given color or bundle is in stock.

The two lasers

Diode Infrared
What xTool prints 455 nm, 10W 1064 nm, 2W
Spot size on the spec table 0.08 × 0.06 mm 0.03 × 0.03 mm
Work xTool assigns it Wood, leather, paper, slate, some dark acrylic, and cutting Metal, plastic, black acrylic

The FAQ names slate under the diode, in the same breath as glass, ceramic, rubber, and fabric. The introduction’s material list says “shale” rather than “slate.” Shale and slate are not the same rock. This page treats the FAQ’s word “slate” as the one that matches a slate coaster, and it does not pretend the introduction’s “shale” line was a lab test of your coaster.

Speed on the spec table tops out at 4,000 mm/s. That is a galvo figure. It is not a cutting speed. Cutting speeds on the settings pages are much slower, and they come from a different source.

Work area, and the page that disagrees

The support spec table and the FAQ both say 115 × 115 mm, and the FAQ calls that about 11.5 × 11.5 cm. The Canada product FAQ says the same base area, and it adds that a slide extension can take the area to 115 × 400 mm.

The US news post says a slide extension increases the working area “fourfold” and does not print a millimeter size. Four times 115 × 115 is not the same sentence as 115 × 400. This page does not average those two xTool sentences. The base area used everywhere else on this site is 115 × 115 mm. If you own the slide extension, measure the framed area in the software before you promise a customer a 15-inch piece.

Processing height on the spec table is 113 mm. The machine itself is 179 × 235 × 334 mm and 4.6 kg.

What a cut is allowed to mean

The introduction says the diode can cut up to 8 mm of wood and up to 5 mm of acrylic, and it limits the acrylic note to “some dark opaque acrylic.” OMTech’s diode warning, written for diode lasers in general, says blue light passes through clear acrylic. That is not an xTool test of the F1. It is a reason not to buy clear acrylic for this diode and hope. Dark acrylic is the phrase xTool actually used.

Framing is not the cut. xTool’s processing article says to close the cover, or to wear goggles that block 455 nm and 1064 nm, while the frame runs. The marketing lines about engraving in public are marketing. Follow the goggle sentence.

Before a settings page

xTool’s material library in the software is aimed at xTool’s own materials. Their processing article says third-party stock should get a material test array first. The slate settings page uses a maker’s published F1 row for that test, and it says the project was cut on a different machine. There is no official F1 number on this site yet for anodized aluminum. Do not borrow the slate row for metal.

Questions people ask

Which laser do I turn on?

xTool's introduction splits the work. The blue diode is the one for wood, leather, slate, paper, and cutting. The infrared laser is the one for metal, plastic, and black acrylic. Only one fires at a time.

How do I focus it?

The quick start guide says to turn the knob until the red and blue light spots overlap. The support article on processing also lets you type a thickness so the head moves itself. For a cut, that same article says to put the focus about halfway through the thickness.

Sources

  1. xTool F1 product introduction — xTool
  2. FAQ on product information for F1 — xTool
  3. xTool F1 quick start guide — xTool
  4. xTool F1 Canada product FAQ — xTool
  5. Introducing xTool F1 — xTool
  6. Process on the baseplate, including framing and focus — xTool