CO2 · Machines

OMTech MF1624-60, a 60W CO2

OMTech lists the MF1624-60 as a 60W CO2 with a 16 by 24 inch bed. The same page prints two different tube-life numbers.

· About 2 min read

Laser
CO2
Wattage
60W CO2
Work area
16 × 24 in (400 × 600 mm)
Specs checked
2026-11-18

What the maker says it can do

  • OMTech's product page rates it at 60W, with a 16 by 24 inch engraving area and a stated top speed of 600 mm/s.
  • OMTech's cutting chart gives 60W speeds for acrylic, a single layer of leather, and wood board. Those speeds are quoted on the settings pages, not rewritten here.
  • The package list includes RDWorks. The page says LightBurn is compatible and is not included.

What it does not do, from the same sources

  • The 60W columns for iron plate on OMTech's cutting chart are dashes. This page does not invent a stainless cutting speed the chart left blank.
  • The chart's PVC rows are not repeated on this site. OMTech's own later article says PVC makes chlorine gas.
  • A 0.4 inch cut is not a settled spec. The specification table calls 0.4 inch a maximum engraving depth, while a paragraph says the machine cuts up to 0.4 inch.

Settings written for this machine

The listing checked on November 18, 2026 is the OMTech Maker MF1624-60. It is a glass-tube CO2 cabinet, not a diode and not a fiber marker.

What the product page prints

The specification table says:

  • Engraving area 16 × 24 in (400 × 600 mm).
  • Rated power 60W.
  • Estimated service life 2,000 hours.
  • Maximum engraving speed 23.6 ips (600 mm/s).
  • Maximum engraving depth 0.4 in (10 mm).
  • Tube length 40 in (1,000 mm) and tube diameter 2 in (50 mm).
  • Front and back pass-through 28.3 × 1.9 in (720 × 50 mm).
  • Certification CE and FDA. The page does not print a laser class in that table.
  • Machine size 44.9 × 29.5 × 26.0 in. Net weight 187 lb.

A paragraph above that table says the tube is good for up to 1,000 hours, and that the life doubles if you stay at lower settings. Another sentence says the machine cuts up to 0.4 inch deep. The table’s phrase for 0.4 inch is “max engraving depth.” Those are not the same claim. A 1/2 inch birch sheet is outside both sentences. Even a 1/4 inch sheet is not a number this page will invent. The 1/8 inch plywood page stays with the rows OMTech actually printed for about 3 mm.

The package list includes keys, an exhaust pipe, water pipes, and a user manual. LightBurn is listed as compatible software that is not included. RDWorks is the bundled software.

What the cutting chart refuses to number

OMTech’s parameter PDF has a 60W column. For iron plate, that column is a dash. Stainless rows in the same file show speeds only once the wattage is much higher, with oxygen noted on the iron line. This cabinet’s page never claims it engraves bare stainless the way a fiber laser does. If you need a mark on bare steel, this is the wrong machine page.

The same PDF prints PVC speeds. OMTech’s material article says laser-cutting PVC makes toxic chlorine gas and hydrochloric acid. This site follows the article. The speeds are not copied. Read safety before you test a plastic that is not labeled.

Where the settings live

Plywood, cast acrylic, vegetable-tanned leather, and glass each have their own page. The numbers there are OMTech’s ranges, or a LightBurn library file that is labeled as someone else’s 60W OMTech, not as a lab log of this cabinet. None of them replace a test on your own sheet. Tube age, lens, and air change the result, which is why the chart and the blog already disagree with each other.

Questions people ask

Is this the 20 by 28 inch OMTech?

No. The page checked for this article is the MF1624-60, and its engraving area line says 16 by 24 inches. The AF2028-60 is a different listing with a 20 by 28 inch bed. Do not copy settings across those two cabinets without a new test.

Why are there two hour ratings?

The product page says the tube delivers 60W for up to 1,000 hours, and that lower settings can double that life. The specification table on the same page says an estimated service life of 2,000 hours. This page does not pick one.

Sources

  1. OMTech Maker MF1624-60 product page — OMTech
  2. OMTech laser cutting recommended parameters — OMTech
  3. Material settings for laser engravers — OMTech