Machine × material · Settings
OMTech 60W settings for 1/8 inch birch plywood
OMTech prints 10–15 mm/s at 80–90% for 1/8 inch plywood on a 40–60W CO2, and a different 3 mm board row at 95%.
- Machine
- OMTech MF1624-60, a 60W CO2
- Material
- Birch plywood, including 1/8 inch
- Rows
- 3
Settings on this page
| Job | Laser | Power | Speed | Passes | Interval | Focus | Where it came from |
|---|---|---|---|---|---|---|---|
| Cut | CO2 | 80–90% | 10–15 mm/s | not stated | not stated | about halfway into the thickness | Cited |
| Cut | CO2 | 95% (the chart note) | 12 mm/s optimal, 15 mm/s maximum | not stated | not stated | not stated | Cited |
| Cut | CO2 | 55% max, 30% min | 20 in the file, read here as 20 mm/s | not set in the file | not set in the file | not set in the file | Starting estimate The file stores speed 20 with no unit, for wood-ply-std at thickness 3. The author says the library is for their own machines and may not work on yours. Twenty millimeters per minute would crawl under a 60W beam, so this page reads 20 as mm/s. The file name says 60W OMTech. It does not say MF1624-60. |
None of these rows is a lab log of Baltic birch on an MF1624-60. They are the closest sentences OMTech and one LightBurn library actually published for a 60W CO2 and a thin wood sheet. The machine page is the 16 by 24 inch cabinet. The material page is why glue and species still matter.
The OMTech store listing is the cabinet. Buy the plywood from a seller who will say what the glue is.
What each row is
The blog row is the one that says “plywood.” It is also the one that says “balsa,” and it covers every CO2 from 40W to 60W. Your tube is the top of that band. The range is 10–15 mm/s at 80–90% power. Passes are not stated. Focus, in the same article’s wood tips, is about halfway into the thickness, not on the top face. Air assist is described as necessary.
The PDF row is the 60W column for “board excluding rare hardwoods,” 3 mm. The chart note says the speeds assume 95% power. For 3 mm the maximum cell reads 15 mm/s and the optimal cell reads 12 mm/s. Thicker rows in that chart are hard to line up on the copy checked on November 18, 2026, so this page does not quote them. 1/8 inch is 3.175 mm, a hair thicker than 3 mm.
The LightBurn row is one person’s file, omt-60w.clb, material wood-ply-std, thickness 3, max power 55, min power 30, speed 20. LightBurn uses the lower power on corners. The readme says the settings are for the author’s machines. See the estimate note in the table for why the speed is read as mm/s.
Run a test grid first
Use an offcut of the same birch. Mask it if you care about the face. Set the focus halfway through, the way OMTech describes for wood cuts. In the test grid, a useful first net for this job is power from about 50% to 90% and speed from about 8 to 20 mm/s. That net covers the blog row and the LightBurn row. It is still a net, not a fourth official number.
Start the real test near 10 mm/s and 80%, the gentle corner of the blog’s own range. If that square falls out with a clean edge, you can try faster. If it chars, do not answer by going slower.
If the edge chars
The line is black, the face is stained past the mask, or the edge is crumbly. You had too much heat. Move toward the faster end of the blog row, or toward the LightBurn power, and keep the air on. OMTech also says a second lighter pass is better than one slow scorch on thicker wood. This sheet is the thin one. Do not add passes until a single pass has failed on scrap.
If it does not cut through
The piece stays attached in the glue line or at a knot. OMTech’s article says cheap plywood has dense spots that will not release on the first pass. Slow down inside the published range before you raise power to the chart’s 95%. Living at 95% is what the chart assumes, and the same company’s later article tells you a glass tube lasts longer at lower settings. The product page itself disagrees about whether that life is 1,000 or 2,000 hours. Either way, 95% is the chart, not a habit.
What would change the number
A different wattage, a dirty lens, weak air, wet wood, or a sheet that is really 1/4 inch. The 1/4 inch row in the blog is an 80W sentence, not a 60W sentence. It is not copied here. Exterior plywood with unknown glue does not belong in this test at all.
Questions people ask
Why are there three different cuts?
Because three sources disagree. OMTech's blog gives a band for plywood and balsa. OMTech's chart gives one speed for generic board at 95% power. A LightBurn file from one 60W owner is lower power and, read as mm/s, a bit faster. The test grid is how you find which corner fits your birch.
Does any source say Baltic birch?
No. The blog says plywood/balsa. The chart says board, excluding rare hardwoods. The LightBurn file says wood-ply-std. Birch is denser than balsa, so start at the slow, lower-power end of the blog row and do not treat 15 mm/s as promised.
Sources
- Material settings for laser engravers — OMTech
- OMTech laser cutting recommended parameters — OMTech
- LightBurn library omt-60w.clb — clvLabs
- LightBurn library readme — clvLabs
- OMTech Maker MF1624-60 product page — OMTech