Machine × material · Settings

OMTech 60W settings for vegetable-tanned leather

OMTech's 60W engrave row is 100 mm/s at 10–15%. Their 40–60W cut for 3–5 ounce veg-tan is 25–30 mm/s at 40–50%, one pass.

· About 3 min read

Machine
OMTech MF1624-60, a 60W CO2
Material
Vegetable-tanned leather
Rows
4

Settings on this page

Job Laser Power Speed Passes Interval Focus Where it came from
Engrave CO2 10–15% 100 mm/s not stated not stated optional, about 1/8 inch out of focus to soften the mark Cited
Cut CO2 40–50% 25–30 mm/s 1 not stated not stated Cited
Cut CO2 95% (the chart note) 17 mm/s optimal, 20 mm/s maximum not stated not stated 50 mm lens recommended in the chart note for 60–100W Cited
Cut CO2 70% max and min 50 in the file, read here as 50 mm/s 2, set in the file not set in the file not set in the file Starting estimate
The file's leather-mid cut is thickness 2, speed 50, power 70, and 2 passes. It does not say vegetable-tanned, and it does not name the unit. This page reads 50 as mm/s for the same reason as the plywood entry in that file. It is one owner's 60W library, not a tannage test.

Read the OMTech MF1624-60, a 60W CO2 page and the Vegetable-tanned leather page for the citations behind the machine and the material.

Only vegetable-tanned leather. The material page has OMTech’s warning on chrome tan and PVC faux leather. The machine is the MF1624-60. The product page does not include a hide.

What each row is

Engraving, from the blog’s 60W CO2 line: 100 mm/s at 10–15% power. Passes and line interval are not in that cell. The same section says you can drop the bed about 1/8 inch out of focus to soften a mark. That is optional. Masking tape keeps the soot off the face. Air stays on.

Cutting 3–5 ounce stock (about 1.2–2 mm), from the blog’s 40–60W line that names OMTech and the K40: 25–30 mm/s, 40–50%, one pass. Eight ounce (about 3 mm) is a different row on that page, 15–20 mm/s at 80–90% and 2–3 passes. It is not the row in this table. If your hide is stamped 8 ounce, do not use the 3–5 ounce line and then complain that it did not cut through.

The chart’s single-layer leather cell for 60W is 20 mm/s maximum and 17 mm/s optimal, at the chart’s 95% note. It does not say vegetable-tanned, and it does not say an ounce weight. The note recommends a 50 mm lens and a small compressor for 60–100W. It is a real OMTech number. It is also a harsh one next to the blog.

The LightBurn leather-mid cut is thickness 2, speed 50, 70% power, two passes. The estimate note explains the unit and the missing tannage. There is a fill in that file at speed 300 and 20% power. This page does not add it as a second engrave row, because the blog already gives a 60W engrave line with a unit written on the page.

Run a test grid first

Use a scrap of the same hide. Tape both faces. For an engrave, test 10% to 20% at about 80 to 150 mm/s, with 100 mm/s and 10–15% inside that net. For a cut, test 40% to 55% at 20 to 30 mm/s before you look at 95%.

If the edge chars

Leather will darken. A brittle, crumbled edge or a wide black halo means too much heat. Raise speed or drop power inside the blog range. OMTech’s damp-hide trick is in their article if the char is the problem and the cut is otherwise through. Strong air helps. Do not answer char by slowing down.

If it does not cut through

Check the ounce weight first. A thick belt hide will not fall out on the 3–5 ounce row, and the fix is the 8 ounce row from the same article, on a new scrap, not a guess past 95%. If the stamp really is 3–5 ounce and the line still hinges, slow toward 25 mm/s at 50% before you touch the chart’s 17 mm/s at 95%.

What would change the number

Dye, finish, moisture, and a hide that is not veg-tan. A diode such as the F1’s 10W laser is a different table. xTool lists leather as something that diode can cut, and this site does not yet have a sourced F1 speed for it.

Questions people ask

Can I use this on a thrift-store jacket?

No. Most garment leather is chrome-tanned. OMTech says that tannage releases hazardous gas and corrodes the machine. If the hide does not say vegetable-tanned, it does not go in.

The chart is much hotter than the blog. Which is the test?

Start on scrap inside the blog's 40–50% cut, or the 10–15% engrave. The chart's 95% row is printed, and it is a hard way to treat a glass tube and a hide. Open it only if the lower row does not cut through.

Sources

  1. Material settings for laser engravers — OMTech
  2. OMTech laser cutting recommended parameters — OMTech
  3. LightBurn library omt-60w.clb — clvLabs
  4. OMTech Maker MF1624-60 product page — OMTech