Machine × material · Settings

OMTech 60W settings for engraving glass

OMTech's 40–60W CO2 glass row is 300 mm/s at 20% power, with a 0.1 mm line interval. It is an engrave, not a cut.

· About 3 min read

Machine
OMTech MF1624-60, a 60W CO2
Material
Glass for engraving only
Rows
1

Settings on this page

Job Laser Power Speed Passes Interval Focus Where it came from
Engrave CO2 20% 300 mm/s not stated 0.1 mm not stated Cited

Read the OMTech MF1624-60, a 60W CO2 page and the Glass for engraving only page for the citations behind the machine and the material.

One cited row. OMTech’s glass table gives a 40W to 60W CO2 engrave of 300 mm/s, 20% power, and a 0.1 mm interval. The MF1624-60 is a 60W CO2, so it is inside the band and at the top of it. The article does not say the row was cut on this cabinet. Glowforge lists glass as engrave-only on a different machine. That supports “do not cut it.” It is not a second speed.

The glass page has the diode warning. Do not run OMTech’s 10W diode glass row on this CO2. The product page is the cabinet.

How to hold the heat down

OMTech says a CO2 does not require a coating, and that a single layer of wet paper towel is a common way to keep the mark from chipping. Smooth out bubbles. If you use the towel, turn air assist off so it does not dry the paper in the middle of the job. That on/off note belongs to the towel, not to the 20% cell.

Paint and marking spray are the other methods in the same article. They have to be dry. Do not spray them in the laser room. A thin tile is the right scrap. A bottle needs a rotary this page does not set up.

Run a test grid first

On a corner of a scrap tile, run 15% to 25% power at 250 to 400 mm/s, with 20% and 300 mm/s in the middle of the net. The interval they printed is 0.1 mm. If your software wants lines per inch, do not let this page convert it for you. Type 0.1 mm if the software has a millimeter interval, and look at the result.

If the mark chars or chips

Glass does not char like wood. The failure is a sandy, chipped mark or a crack. That is too much heat in one place. Go faster than 300 mm/s, or leave the power at 20% and add the damp towel, before you drop the speed. A crack means stop. Do not finish the job on that piece.

If the mark is too light

Look at focus and at whether you are engraving the face you think you are. A towel that is too wet can steal the mark. Speed down a little inside the test net, still near the published 300 mm/s, before you raise power past 20% on a 60W tube. If the glass is clear and you are somehow on a diode profile, you are on the wrong laser. This cabinet is CO2. The diode note does not apply, and a missing mark on a CO2 is usually focus or a towel, not a missing coating.

What would change the number

Tempered glass, a curved bottle, a painted window, or a mirror. Mirrors reflect. Glowforge warns that chrome and copper can reflect a CO2 beam back into the machine. Do not engrave the mirror side. A different wattage is a different row. OMTech’s 80–100W glass line is not this one.

Questions people ask

Is 20% a lot on a 60W tube?

The row is for the whole 40–60W band, and the MF1624-60 sits at the top of it. Twenty percent of 60W is more light than 20% of 40W. Start the test at 20% and 300 mm/s, and be ready to go faster or lighter if the glass chips. Do not invent a lower percent and call it OMTech's.

Do I need black paint?

Not for a CO2. OMTech says a CO2 is absorbed by glass without a coating, and that many people still use a damp paper towel to spread the heat. A blue diode does need a dark coat. This page is the CO2.

Sources

  1. Material settings for laser engravers — OMTech
  2. Glowforge Performance series tech specs — Glowforge
  3. OMTech Maker MF1624-60 product page — OMTech