Machine × material · Settings

xTool S1 40W settings for 1/8 inch birch plywood

xTool's S1 table gives 3 mm basswood 100% at 15 mm/s, one pass. It does not say birch. A 40W review cut 1/8 inch birch at 17 mm/s and left power out.

· About 7 min read

Machine
xTool S1 40W enclosed diode laser
Material
Birch plywood, including 1/8 inch
Rows
2

Settings on this page

Job Laser Power Speed Passes Interval Focus Where it came from
Cut Diode 100% 15 mm/s 1 not stated not stated Starting estimate
The xTool S1 tab prints Lindenholz, 3.0 mm, vector cut, 40 W blue laser, as 100 / 15 / 1. The column header is power in percent, speed in mm/s, and passes. Lindenholz is basswood. The cell does not say birch or plywood. The US product page prints the same 15 mm/s as the one-pass maximum for 3 mm basswood on the 40W, and it does not print a power or the word birch. One-eighth inch is 3.175 mm, which is 0.175 mm thicker than 3.0 mm. This row is that basswood cell used as a start for birch plywood, not a birch measurement.
Cut Diode not stated 17 mm/s, also written as 1000 mm/min 1 not stated not stated Cited

Check price on Amazon

As an Amazon Associate I earn from qualifying purchases.

Read the xTool S1 40W enclosed diode laser page and the Birch plywood, including 1/8 inch page for the citations behind the machine and the material.

xTool’s own S1 table does not have a birch row. The machine page is the 40W diode, with a work area of 19.61 by 12.56 inches. The birch page is why the glue and the species still matter. The two rows below are the closest published numbers, and they are not the same kind of number.

The machine, if you are buying one, is the xTool S1 listing. Confirm the variant still says 40W.

What each row is

The first row is xTool’s, and it is basswood. On the German material page, the xTool S1 tab has a wood table. The 3.0 mm vector-cut line for the 40 W blue laser reads 100 / 15 / 1. The header says that triple is power in percent, speed in millimeters per second, and passes. The material name on that line is Lindenholz. Lindenholz is basswood, not birch. The thickness cell is 3.0 mm, not 1/8 inch. Interval and focus on that line are blank. xTool’s own note on the page says that if your material is missing, you can try a similar one. That is all this row is.

The US product page agrees with the speed and still does not rescue it. Its one-pass speed table prints 15 mm/s for 3 mm basswood on the 40W. It does not print a power there, and it does not say birch. The separate thickness table says the 40W can cut 15 mm of basswood plywood in one pass. That is a maximum thickness, not a speed for 1/8 inch birch.

The second row is one reviewer’s cut, not a chart. Chris Hoffman’s October 20, 2023 S1 40W review says he was cutting 1/8 inch birch plywood at 1000 millimeters per minute, which he also writes as 17 mm per second, and that it went through in a single pass. Power, interval, and focus are not in that paragraph. The review prints both 1000 mm/min and 17 mm/s. This page does not “correct” that rounding. It also does not invent the power he left out. He received the machine from xTool for the review. It is one sheet, in one shop, in 2023.

The same German file does contain the word birch. Those lines say Birkensperrholz, and the module column says D1 Pro. The 3.0 mm cut for the D1 Pro 20W is 100 / 6 / 1. A 20W gantry diode is not this enclosed 40W. Do not type 6 mm/s into the S1 because the word birch finally appeared.

An OMTech CO2 speed does not transfer either. The 60W birch page is a glass tube. Leave it there.

Run a test grid first

Use an offcut of the same birch, with the same glue and the same moisture. Mask both faces if the show face matters. xTool’s plywood guide says beige masking tape takes the tar, and a honeycomb or slat keeps the sheet off the metal bed so the back does not carbonize where it touches. That guide also says to turn air assist on for a plywood cut.

In the test grid, a useful first net is power from about 70% to 100% and speed from about 10 to 20 mm/s, one pass. That window holds the basswood cell at 100% and 15 mm/s, and the review’s 17 mm/s. It is a net around two published figures. It is not a third official speed.

Start the real square at the basswood cell: 100% and 15 mm/s, one pass, on the blue diode, with air on. If that square falls out and the edge is acceptable, you can look at the faster review speed. If it chars, do not answer by going slower.

Route the exhaust hose outside or into a purifier, the way the S1 user guide describes. Keep the lid closed. xTool’s safety page says the interlock should stop the job if the lid opens, and it says not to cut PVC, vinyl, or a plastic you cannot name. Birch is wood. A vinyl mask is not. Read safety if the sheet’s glue or coating is a mystery.

If the edge chars

The cut is black, the face is stained past the tape, or the edge is crumbly. You had too much heat. The basswood cell is already at 100%, so the next square is a faster one inside the test, still one pass, still with air. xTool’s plywood guide treats a dirty lens as a cause of a bad edge. Wipe the lens before you decide the wood is the problem.

Do not add a slower pass to “clean up” a charred line. More time under a 40W spot is more char.

If it does not cut through

The piece hangs at a glue line or a knot. The basswood cell is one pass at 15 mm/s. The review’s birch cut was one pass at 17 mm/s and did fall out, on that author’s sheet, at a power he did not print. Try a slower square before you invent a second pass. xTool’s cut-through article says to use the software preset when the material is listed, then to lower the speed and, if needed, add passes. Birch is not the listed material. A second pass is a test, not a number from the basswood cell.

Focus is the other lever, and it is still not a birch cell. xTool’s focus article says that for stock about 3 mm and thicker, sinking the focus by 3 mm helped in their lab, that the control in XCS runs from 0 to 6 mm, and that the sink must not go past the thickness or the head can hit the sheet. One-eighth inch is 3.175 mm, so a 3 mm sink is still inside the sheet by a fraction of a millimeter. Their cut-through article also says to set focus lowering to 3 mm. Both articles are general. Neither one names birch. The table on this page leaves focus as not stated for that reason. If you try a sink, stay inside the sheet you measured, and try it on scrap.

The cut-through article’s air setting of level 4 is written for thick or tough material, and it needs the air-assist set. It is not a birch cell either. The plywood guide’s instruction is the simpler one: air assist on.

What would change the number

A 20W module. The same S1 table prints 100 / 7 / 1 for 3.0 mm Lindenholz on the 20 W blue laser. The product page’s 10W column prints 5 mm/s as the one-pass maximum for 3 mm basswood. Those are other heads.

A thicker sheet. The next basswood cut on the S1 table is 6.0 mm at 100 / 10 / 1. One-quarter inch is 6.35 mm, and it is still basswood in that table, not birch. It does not belong on this page.

The infrared head, a wet board, weak air, no honeycomb, or a sheet whose glue you cannot name. Exterior plywood stays out of the test until you know the glue. A tired lens or a lid that was open for “just a look” will also make a good row look false. Fix those before you write a new speed in the margin.

Gear we recommend

Accessories for a careful setup. Each link is an Amazon search, so you can read the listing before you buy. The glasses link is for a diode laser, 445 nm. A CO2 pair is a different product. A search is not a rating, and it is not a substitute for the manual.

As an Amazon Associate I earn from qualifying purchases.

Questions people ask

Why is 15 mm/s marked as an estimate?

Because the cell says Lindenholz, which is basswood, at 3.0 mm. Birch plywood is a denser sheet with glue lines, and 1/8 inch is 3.175 mm. The power, the speed, and the single pass are copied from that cell. The material is not the sheet xTool named, so the row is a starting estimate.

What power did the 17 mm/s birch cut use?

The review does not say. It names an S1 40W, 1/8 inch birch plywood, 17 mm/s, and a single pass, and it also writes 1000 millimeters per minute. This page does not fill in 100% for that test. The only power xTool printed for a 3 mm wood cut on this module is the basswood row.

Can I use the birch row from the D1 Pro?

No. The same German page has a birch plywood cut, and the module column says D1 Pro 20W, at 100 / 6 / 1 for 3.0 mm. That is a different machine and half the wattage. It is not a setting for this S1.

Sources

  1. Materialeinstellungen für xTool Maschinen — xTool
  2. xTool S1 product page — xTool
  3. Hoffman Engineering xTool S1 review — Hoffman Engineering
  4. Beginner's guide to plywood laser processing — xTool
  5. xTool S1 focus lowering — xTool
  6. xTool S1 will not cut through — xTool
  7. S1 safety first — xTool